Sharp AR-505 Operation Manual Download

Page: 89 / 174

5-3

CHAPTER

(A)

Open the feeding roller cover.

If a misfed original is in the feeding section:

Move the release lever in the direction of the arrow and
remove the misfed original.

If a misfed original is in the transport section:

Open the paper guide.

Rotate the roller in the direction of the arrow and gently

remove the misfed original. Close the paper guide after
removing the misfed original.

Close the feeding roller cover firmly by pressing in the
middle of the cover.

●

Be sure to open and close the document feeder to cancel the
misfeed display.

MISFEED REMOVAL

COPIER TROUBLE?

Misfeed removal

Feeding roller cover

Release lever

Paper guide

Roller

Summary of Contents for AR-505















































































































































































Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands

Sharp AR-505, Operation Manual

Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands