Sharp AR-505 Operation Manual Download

Page: 21 / 174

2-7

CHAPTER

1-sided copies from 2-sided originals

Adjust the original guides to the size of the originals and
set the originals face up in the document feeder tray.

Press the 2-SIDED COPY key.

Press the

key on the touch panel.

Press the “OK” key.

Enter the desired number of copies.

Press the START (

) key.

●

To cancel a copy run, press the CLEAR ALL (

) key. Copying

will stop and the RSPF will output any originals which have been
fed. Also, the number in the copy quantity display will be reset to
0.

MAKING COPIES

Using the RSPF

USING THE RSPF

AUTO

PROGRAM

AUDIT CLEAR

INT

CLEAR ALL

START

READY TO COPY.(DOCUMENT FEEDER MODE)

2-SIDED COPY

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

READY TO COPY.(DOCUMENT FEEDER MODE)

2-SIDED COPY

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

Maximum height
line

Summary of Contents for AR-505















































































































































































Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands

Sharp AR-505, Operation Manual

Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands