Sharp AR-505 Operation Manual Download

Page: 9 / 174

1-5

CHAPTER

POWER ON AND OFF

The power switch is located on the left side of the copier. When the
power switch is turned to the “ON” position, the message “

WARMING

UP. PLEASE WAIT.

” will appear in the message display. Warming

up takes less than 150 seconds. Once the copier is ready, the
message display will change to “

READY TO COPY.

”, and the START

(

) key indicator will light up, indicating that copying is possible.

If the copier has been programmed in the auditing mode, the message
“

ENTER YOUR ACCOUNT NUMBER. -----

” will appear. Once a valid

account number has been entered, copying will become possible.

GETTING STARTED

Power on and off

Power on

Power off

Summary of Contents for AR-505















































































































































































Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands

Sharp AR-505, Operation Manual

Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands