Sharp AR-505 Operation Manual Download

Page: 80 / 174

4-2

CHAPTER

PAPER

Types and sizes of copy paper

Size

Weight

Capacity

Special paper

(80

(21lb.)

paper)

Paper trays

A5 to A3

56 to 105

500 sheets

1 and 2

(5-1/2" x 8-1/2"

(15 lbs. to 28 lbs.)

to 11" x 17")

Bypass tray

Face up

A6 to A3

52 to 128

50 sheets

Transparency film,

delivery

(5-1/2" x 8-1/2"

(14 lbs. to 34 lbs.)*

labels, tracing paper,

to 11" x 17")

(Ordinary paper)

176

(65 lb.)

paper**, 200

(110 lb.) paper**

Face down A5 to A3

56 to 105

50 sheets

delivery

(8-1/2" x 11"

(15 lbs. to 28 lbs.)

to 11" x 17")

●

For best results, use only paper recommended by SHARP.

* For paper weighing from 105 to 128

(28 to 34 lbs.), A4 (8-1/2" x 11")

is the maximum size that can be fed through the bypass tray.

** Paper heavier than 128

(34 lbs.) must be fed narrow side into the

feed slot of the bypass tray.

★

KEY OPERATOR To enable face down delivery from the bypass tray,
paper type setting in the bypass tray must be enabled. See page 8-22.

Loading copy paper

“

OPEN TRAY AND ADD PAPER.

” will be displayed when there is

no copy paper in a selected paper feed station.
When a selected paper tray is not installed or is improperly installed,
“

PUSH PAPER TRAY INTO THE MACHINE UNTIL IT

LATCHES.

” will be displayed. Install it or push it back firmly into

place.
For best results, use only Sharp recommended paper.

SUPPLIES

Paper

Summary of Contents for AR-505















































































































































































Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands

Sharp AR-505, Operation Manual

Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands