Sharp AR-505 Operation Manual Download | Manualshive

Page: 118 / 174

background image

7-6

CHAPTER

7

Staple sort

The STAPLE SORT mode staples A4, A4R, B4, and A3 (8-1/2" x 11", 8-1/2" x
11"R, 8-1/2" x 14", and 11" x 17") size copies. Stapled sets cannot be delivered to
the top tray.

●

In the STAPLE SORT mode, copying will automatically stop when the number
of copies output in the offset tray exceeds certain limits regardless of the tray
capacity. In that case, follow the message on the screen. Such limits vary with
the size of copy paper.

NOTE:
Different size originals cannot be copied onto copy paper of their respective sizes
in the STAPLE SORT mode. The paper size selected for the first scanned original
will be used for all originals. To copy different size originals in the STAPLE SORT
mode, select the paper size for the largest original.

Using the RSPF

1

Set the originals in the document feeder tray.

●

If the number of copies in one set is more than 50 for
A4 or A4R (8-1/2" x 11" or 8-1/2" x 11"R) paper or 25 for B4 or
A3 (8-1/2" x 14" or 11" x 17") paper, the copies will not be
stapled.

●

The stapling position shown in the left figure is the factory de-
fault position.

2

Press the OUTPUT key.

3

Press the “STAPLE SORT” key on the touch panel.

OPTIONAL EQUIPMENT

Finisher (AR-FN3)

FINISHER (AR-FN3)

AUTO

EXPOSURE

Stapling position

READY TO COPY.(DOCUMENT FEEDER MODE)

OUTPUT

TOP TRAY

OFFSET

SORT

OFFSET

TRAY

STAPLE

SORT

GROUP

OK

AUTO

EXPOSURE

PAPER SELECT

100%

COPY RATIO

AUTO A4

«
...
116
117
118
119
120
...
»

Summary of Contents for AR-505















































































































































































Reviews:

No comments

Related manuals for AR-505

Brand: Panasonic Pages: 16

U1 - Toughbook - Atom Z520

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 63

Brand: Panasonic Pages: 180

Brand: ZipRip Pages: 64

Copycentre C118

Brand: Xerox Pages: 2

Brand: Canon Pages: 58

Brand: Oce Pages: 206

Brand: Olivetti Pages: 160

Brand: Oki Pages: 2

Brand: Oki Pages: 156

Brand: Lexmark Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands