Sharp AR-505 Operation Manual Download

Page: 101 / 174

5-15

CHAPTER

COPIER TROUBLE?

Troubleshooting

TROUBLESHOOTING

Problem

Solution

Paper misfeeds frequently.

Dust, dirt, smudges appear
on copies.

Black lines appear on copies
when using RSPF.

●

Non-standard paper used?

●

Is paper properly installed?

●

Pieces of paper inside copier?

●

Paper curled or damp?

●

Document glass, document feeder
cover dirty?

●

Is the scanning section glass or
the scanning guide of the RSPF
dirty?

Use standard paper.
If using special papers, feed the paper
through the bypass tray.

See pages 2-14 and 4-2.

Remove all pieces of misfed paper.
See page 5-2.

Store copy paper flat in the wrapper in
a dry location. See page 4-8.

If a problem persists after checking the above, please consult your key
operator prior to contacting your authorised Sharp Service Centre.

Self-diagnostic function

An automatic self-diagnostic function is built into this copier. Should the
copier malfunction, the self-diagnostic function will locate the problem
and stop the copier to prevent damage. An alphanumeric code will
appear in the message display.

Example
Should the copier stop completely, and the message “

CALL FOR

SERVICE. CODE:

” appear in the message display, contact your

authorised Sharp Service Centre.

★

KEY OPERATOR

See page 8-32.

Clean regularly. See page 6-6.

Clean regularly.
See page 6-6.

Touch panel is too dark or
too light.

●

Is LCD contrast properly
adjusted?

Adjust the LCD contrast.
See page 6-7.

Summary of Contents for AR-505















































































































































































Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands

Sharp AR-505, Operation Manual

Search results

Summary of Contents for AR-505

Reviews:

Related manuals for AR-505

Brands by name

Popular brands