Sens SG-A1 User Manual Download

Page: 57 / 100

SENS.413347.015RE
57

9 TRANSPORTATION AND STORAGE

9.1 Transportation conditions must comply with GOST 15150 with ambient temperature

from minus 40°C to plus 50°C. Transportation conditions - 5 (OZh4).

9.2 Storage conditions for packed product - 5 (OZh4) as per GOST 15150 with ambient

temperature from minus 40°C to plus 50°C. Storage conditions after unpacking - I (L)
according to GOST 15150.

9.3 Designated storage life of device - 15 years (included in service life).

10 UTILIZATION

Utilization of gas detector shall be carried out in accordance with laws of the Custom

Union member countries, following the instruction of Operator organization.

11 MANUFACTURER'S WARRANTY

11.1 Warranty period

– 24 months from the Manufacturer shipping date.

The Manufacturer takes obligation to fix defects revealed by Customer throughout

warranty period, taking into account following storage, transportation, installation and
operation conditions by the Customer.

Summary of Contents for SG-A1





































































































Search results

Summary of Contents for SG-A1

Reviews:

Related manuals for SG-A1

Brands by name

Popular brands

Sens SG-A1, User Manual

Search results

Summary of Contents for SG-A1

Reviews:

Related manuals for SG-A1

Brands by name

Popular brands