Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual Download Page 24

Page: 24 / 138

Overview of Printer Connections

Environmental Controls and Humidity

The Fast T-Jet Blazer Pro should not be exposed to direct sunlight, direct airflow,

dusty areas, any strong magnetic forces or excessively high humidity. The

machine does not like to be too dry or too moist with a level of 40% to 80%

relative humidity being ideal. Since you will be handling wet ink to refill the Bulk

System ink bottles, you should also protect any carpet or floor covering with

mats.

Ensure the entire printer base is sitting on a level, stable surface to support the

weight of the machine. This means all ground support feet must be safely on the

same support surface.

Like any Hi-Tech electronic device, your inkjet printer does NOT like being in

a hot or cold shop or a garage without proper air-conditioning controls. If

left unattended for days or weeks in a hot dry environment, the Print Head

WILL clog. Consult

Chapter 10

for instructions on installing refillable cleaning

cartridges if you anticipate not using your machine for an extended period.

For convenience and efficiency, place your Fast T-Jet Blazer Pro close to the

Heat Press or Conveyor Dryer you will be using to cure the ink. If you have two or

three printers set up as a production work station, arrange them around or near

Fast T-Jet Blazer Pro User’s Manual

Summary of Contents for Fast T-Jet Blazer Pro











































































































































Search results

Summary of Contents for Fast T-Jet Blazer Pro

Reviews:

Related manuals for Fast T-Jet Blazer Pro

Brands by name

Popular brands

Screen Print & Inkjet Fast T-Jet Blazer Pro, User Manual

Search results

Summary of Contents for Fast T-Jet Blazer Pro

Reviews:

Related manuals for Fast T-Jet Blazer Pro

Brands by name

Popular brands