manualshive.com logo in svg

Screen Print & Inkjet Fast T-Jet Blazer Pro, User Manual

Share
Download
Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual Download Page 107

Lubricating the two Main Rails will 

prevent oxidation (rust) and debris build-

up, allowing the Printer Assembly to travel 

freely. This will help prevent registration 

issues that can occur in multiple pass 

prints.

To correctly lubricate the Main Rails, apply a very THIN coat of the 

2. 

same Lithium-based grease used for the Rail Guides. Spread the White 

Grease along the ENTIRE length of both Rails using a clean, lint-free 

cloth. DO NOT use any other lubricate, such as WD-40 or Machine Oil, 

or you risk contamination of the Rail Guides. 

Do Not Lubricate the Drive Screw

The Drive Screw MUST NEVER be lubricated or wiped off with a chemical solvent. 

This is due to a special coating that has already been placed on the Drive Screw 

to prevent dust buildup that could potentially hinder the fluid movement of the 

Printer Assembly. Treating the Drive Screw will allow dust buildup, contaminating 

the drive mechanism. 

Drive Screw

Chapter 10- Preventative Maintenance

and Problem Solving

93

Main Rail- One per side

 

        Two in Total

Summary of Contents for Fast T-Jet Blazer Pro











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands