manualshive.com logo in svg

Screen Print & Inkjet Fast T-Jet Blazer Pro, User Manual

Share
Download
Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual Download Page 44

At this point, you MUST turn OFF the printer. You CANNOT print or 

perform any additional maintenance routines on your machine 

without powering OFF your printer upon completion of a Head 

Alignment. You do not need to perform a complete shut

down- turning OFF the power by using the UI is sufficient.

After your printer has completed its shutdown cycle, your may turn it back ON 

and either begin printing or perform another Head Alignment to check the 

results of your previous calibrations. Keep in mind, you may be required to 

perform 2-3 Head Alignment procedures to initially calibrate your machine for 

printing.

If you perform another Head Alignment, you will again be required 

to choose and enter the best lines and color swatches from each 

group. You CANNOT exit early from this routine. If you do no wish 

to make any further changes, just accept the default values (by 

pressing the Enter key) as they appear in the LCD Display until the 

routine is complete.

Using the Epson LFP Remote Panel

You also have the option of perform 

Uni-Directional and Bi-Directional Print Head 

Alignments from your computer. In addition, 

you can execute a Nozzle Check and  Power 

Cleaning using the Epson LFP Remote Panel.

The Epson LFP Remote Panel can be installed on your computer from the Epson 

Stylus Pro 4800 Driver CD that came with your Fast T-Jet Blazer Pro or you can 

download the 

Remote

 

Panel

 

Utility

 from Epson’s website, 

www.epson.com

. 

Select 

Drivers & Support

 and select the applicable version for the Stylus Pro 4800 

based on your Operating System (Windows XP, Vista, 2000 or MAC)

With the Epson Remote Panel installed and your computer connected to your 

printer, you will need to place the Fast T-Jet Blazer Pro into “Ready (Roll)” mode 

to enable the software to communicate with your machine. If the printer is not in 

“Ready (Roll)” mode, your will receive a “Communication Failed” error.

To place your printer into “Ready (Roll)” mode, it must be at the Index Position. 

This is accomplished by placing the printer in “Ready (Sheet)” mode while the 

Print Assembly is in the 

Home 

position. From “Paper Out (Roll Cut)” mode, aka 

Print

 status, press the LEFT arrow twice.

EPSON LFP Remote Panel.lnk

30

Fast T-Jet Blazer Pro User’s Manual

Summary of Contents for Fast T-Jet Blazer Pro











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands