manualshive.com logo in svg

Screen Print & Inkjet Fast T-Jet Blazer Pro, User Manual

Share
Download
Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual Download Page 100

Fast T-Jet Blazer Pro User’s Manual

86

Clean the Encoder Strip DAILY

Press the Carriage Release Button (page 25) 

to free the Print Carriage from the Capping 

Station. Manually move the carriage to the 

center of the Assembly. This will allow you to 

clean the capping station side of the Encoder 

Strip.

You can use foam-tipped swabs, water, glass 

cleaner or cleaning fluid, but for best results 

use Isopropyl Alcohol pads. Do NOT use 

Rubbing Alcohol pads. Wrap the alcohol pad around both sides of the Encoder 

strip and gently move the pad in both directions. If the pad becomes black, 

use a new pad and clean the Encoder Strip again. Manually return the Print 

Carriage back to the Capping Station to clean the rest of the Encoder Strip. 

Allow the Encoder Strip AIR DRY.

The Encoder Strip is actually translucent with small marks on it. Be 

careful to NOT scratch it or the Print Head sensor will not read it 

correctly. Only use FOAM TIP cleaning swabs or Isopropyl Alcohol 

Pads when doing any maintenance or cleaning inside your Fast 

T-Jet Blazer Pro.

Turning Off Your Printer 

Turn OFF the machine at night using the Circuit Breaker 

Switch. Wait for the printer to completely power down 

(the Print Carriage will dock onto the capping station), 

then turn off the main Power Switch located next to 

the AC cord. DO NOT turn off your printer at the power 

strip. 

Do Not Overfill the Bulk Ink Bottles

When refilling the bulk ink bottles, STOP at the 200ml 

line marked on the front of the bottle. This will prevent 

excess pressure from building up within the cartridge, 

which can cause ink to drip from the Print Head.

Summary of Contents for Fast T-Jet Blazer Pro











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands