Screen Print & Inkjet Fast T-Jet Blazer Pro User Manual Download Page 27

Page: 27 / 138

Connecting Your Printer to a Computer

You may only connect the Fast T-Jet Blazer Pro to

a computer with a USB 2.0 cable. For best results,

you should use the special gold tipped USB cable

supplied with the machine. Avoid using a cable

that is over 6ft in length and do not use a switch

box or USB Hub. failure to follow thee guidelines can

cause communication problems between the printer and your PC.

Including your printer, mouse and Dongle, you will need 3 free USB ports.

Your computer must use a Windows Operating System, such as Windows XP or

Vista (Windows ME is not supported). For best results you should use a computer

with at least 1GB of RAM (2 GB if using Vista). RAM is inexpensive and if you can

put more in your computer, it will prevent problems when printing large files.

The Universal Serial Bus – USB – method of communication

is standard on all newer computers, but a little known

fact is that there is only a certain amount of power

supplied to the entire “bus.” If you have several items

(other than a mouse and the FastARTIST Dongle) plugged

into different USB ports on your computer, this may cause

communication issues with the printer.

We recommend using a dedicated computer to control your Fast

T-Jet Blazer Pro. Avoid using extra USB ports for items (such as a

webcam, joystick, additional printer etc.) when printing with your

Fast T-Jet Blazer Pro.

Failure to follow the recommended environmental, power,

maintenance and operating conditions can void your warranty.

The Fast T-Jet Blazer Pro does NOT like to be in a hot, dry shop with

excess dust, as well as being plugged into outlets with several

other items. Please read and understand the operating conditions

and maintenance requirements for your investment.

Getting Ready to Print

Your Fast T-Jet Blazer Pro uses a specially designed Bulk Ink System with

cartridges that hold about 200 ml of ink per color (x8) and allow for easy re-filling

as needed. In order to prevent damage and ink leakage, your printer was not

shipped with the Bulk System installed. To prevent components from drying out,

Chapter 2- Unpacking and Setup

Summary of Contents for Fast T-Jet Blazer Pro











































































































































Search results

Summary of Contents for Fast T-Jet Blazer Pro

Reviews:

Related manuals for Fast T-Jet Blazer Pro

Brands by name

Popular brands

Screen Print & Inkjet Fast T-Jet Blazer Pro, User Manual

Search results

Summary of Contents for Fast T-Jet Blazer Pro

Reviews:

Related manuals for Fast T-Jet Blazer Pro

Brands by name

Popular brands