schmersal PSC1-C-10 Series Installation Manual Download Page 42

Page: 42 / 173

Installation manual

PSC1-C-10 Installation manual V2.6

Page 42 of 173

Version: 57E

Safety instructions:

•

For a safety-related assessment of the sensor sub-system, the information from the
manufacturer (MTTF

, PFH figures etc.) is to be used.

•

The DC values stated in the table are to be used conservatively and compliance with the
boundary conditions (see "Comments" in table) ensured.

•

Fault exclusions are allowed according to the applicable standards. The boundary conditions
listed are to be ensured over the long-term.

•

If several sensor systems are necessary for the correct function of an individual safety
function, their partial values are to be combined correctly according to the method selected.

Summary of Contents for PSC1-C-10 Series














































































































































































Search results

Summary of Contents for PSC1-C-10 Series

Reviews:

Brands by name

Popular brands

schmersal PSC1-C-10 Series, Installation Manual

Search results

Summary of Contents for PSC1-C-10 Series

Reviews:

Brands by name

Popular brands