schmersal PSC1-C-10 Series Installation Manual Download Page 166

Page: 166 / 173

Installation manual

PSC1-C-10 Installation manual V2.6

Page 166 of 173

Version: 57E

12.3.8.2

Validating FUP against IL and parameters using validation report

The programming in the FUP is to be compared with the IL listing in the validation report.

Example IL listing in the validation report

Validation report

PLC program
Index

Command Operand

Validated

NO1

SLI_EN.1

NO1

SLI_EN.2

NO1

SLI_EN.3

NO1

SCA_EN.1

NO1

SCA_EN.2

NO1

SCA_EN.3

NO1

SLS_EN.2

NO1

SCA_EN.4

NO1

SLS_EN.3

NO1

SLS_EN.4

NO1

SLI_EN.5

SQH

I0.00

MX.2

SQC

SQH

I0.02

AND

I0.03

MX.3

SQC

A stepwise check is recommended. The check is all the more efficient the more the programming in
the FUP has been structured.

Summary of Contents for PSC1-C-10 Series














































































































































































Search results

Summary of Contents for PSC1-C-10 Series

Reviews:

Brands by name

Popular brands

schmersal PSC1-C-10 Series, Installation Manual

Search results

Summary of Contents for PSC1-C-10 Series

Reviews:

Brands by name

Popular brands