Samsung SCX-6320F Service Manual Download Page 91

Page: 91 / 208

Alignment & Adjustments

Service Manual

6-21

Samsung Electronics

6.5.1 NIC Card F/W Upgrade

There're two methods for upgrading NIC f/w. You can not do it by using Printer RCP.

A. SyncThru :

SyncThru

->Menu
->Maintenance
->Upgrade Firmware
->Select the machine you want to upgrade.
-> Fill file path and name in File name field.
->Press Start.

Upgrading NIC F/W will take at least one minute.

B. SyncThru Web Service :

Open a browser(Internet explore)

-> type your machine ip address in address field.
-> Maintenance Tab
-> Firmware Upgrade
-> Fill file path and name in File name field.
-> Press "Upgrade" button

Upgrading NIC F/W will take at least one minute.

Summary of Contents for SCX-6320F

















































































































































































































Search results

Summary of Contents for SCX-6320F

Reviews:

Brands by name

Popular brands

Samsung SCX-6320F, Service Manual

Search results

Summary of Contents for SCX-6320F

Reviews:

Brands by name

Popular brands