manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 128

Troubleshooting

Service Manual

7-31

Samsung Electronics

Ghost & Image
Contamination

• The printed image is too

light or dark, or partially
contaminated black.

• Totally contaminatedblack.

(Black image printed out)

1. The printed image is too light or

dark, or partially contaminated
black.

(1)Check whether foreign sub

stance or toner are stuck to
the terminal(point of contact)
of the toner cartridge.

(2)Check whether the terminal

assembly is normal.

2. Totally contaminated black.

(Black image printed out)

(1)Check whether foreign sub

stances are stuck to the terminal
(point of contact) of the toner
cartridge and the drum cartridge
and the state of assembly. 
(Especially check the charged
roller terminal.)

1. All of 1, 2, 3 above

(1)Remove toner and foreign

substances adhered to the
contact point of the toner 
cartridge.

(2)The contact point of the unit

facing that of the toner cartridge
also must be cleaned.

(3)If the terminal assembly is

unsafe:

• Fully stick the terminal to or

reassemble it after disassembling.

• Disassemble the side plate and

push the terminal to be stuck,
then reassemble it.

2. In case of 2

It is a phenomenon when the
OPC drum of the drum cartridge
is not electrically charged. Clean
the terminals of the charged
roller, then recheck it.

Fault

Signs

Cause & Check 

Solution

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands