manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 78

Service Manual

Alignment & Adjustments

6-8

Samsung Electronics

6.2.6  Duplex Jam

If paper jam occurs in the duplex mechanism, "Duplex Jam" appears on the display.

1)  Press the release lever to open the side cover.

2)  Remove the jammed paper. Then close the side

cover

6.2.8  Optional Tray2 Jam

If paper is jammed in the optional tray2, ‘Jam0 In Tray2’ appears on the display.

1) Pull the paper Tray to open. After you pull it out

completely, lift the front part of the Tray slightly up
to release the Tray from the machine

2)  Remove the paper in the direction shown. To

avoid the paper torn, pull it out gently and slowly.

6.2.7  Bypass Tray Jam

“Bypass Jam” appears on the display when you try to print using the Bypass Tray and the machine does not
detect paper due to no paper or improper paper loading.

“Bypass Jam” also may occur when the paper is not properly fed into the machine through the Bypass Tray. In that
case, pull the paper out of the machine.

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands