Samsung SCX-6320F Service Manual Download Page 76

Page: 76 / 208

Service Manual

Alignment & Adjustments

6-6

Samsung Electronics

6.2.4 Fuser Area

If the paper jams in the fuser area, "Paper Jam 1" appears on the display:

NOTE: The fuser area is hot. Take care when removing paper from the machine.

1) Lift the release lever to open the side cover.

2) Pull down on the fuser lever as shown below.

This will release pressure on the paper. If paper is
not seen in this area, skip to the Exit Area.

NOTE: Do not pull paper up through the fusing unit.

Unfused toner may adhere to the area, result-
ing in smudged copies.

3) Remove the jammed paper, in the direction shown.

4) Push the fuser lever up, and then close the side

cover.

Summary of Contents for SCX-6320F

















































































































































































































Search results

Summary of Contents for SCX-6320F

Reviews:

Brands by name

Popular brands

Samsung SCX-6320F, Service Manual

Search results

Summary of Contents for SCX-6320F

Reviews:

Brands by name

Popular brands