Samsung SCX-6320F Service Manual Download Page 102

Page: 102 / 208

Troubleshooting

Service Manual

7-5

Samsung Electronics

Dark image

1. LSU light power normal?

2. Bias voltage output is high?

3. Video data is always supplied?

4. Bad high charge voltage contact.

1. Check the rated level and replace.

2. Set to power rating.

3. Replace defected board.

4. Check the charge voltage or change the

drum cartridge.

Error Status

Check

Solution

Digital Printer
Digital Printer

Background

1. High voltage output is normal?

2. C/R of drum cartridge is contaminated?

1. Adjust to the rated status.

2. Replace drum cartridge.

Digital Printer
Digital Printer
Digital Printer
Digital Printer
Digital Printer

Ghost

1. High voltage output.

2. Pre-Transfer Lamp.

3. Bad high voltage contact.

1. Check every high voltage.

2. Check the turn-on PTL, LED crash.

3. Clean the inside machine or replace drum

cartridge.

Digital Printer

Stains on back of
paper

1. Contamination of transfer roller.

2. Stains of paper path.

3. Pressure roller’s contamination.

1. Clean the transfer roller with vacuum cleaner.

2. Clean the area of paper path with cloth or

air cleaner.

3. Remove fuser and replace it.

Summary of Contents for SCX-6320F

















































































































































































































Search results

Summary of Contents for SCX-6320F

Reviews:

Brands by name

Popular brands

Samsung SCX-6320F, Service Manual

Search results

Summary of Contents for SCX-6320F

Reviews:

Brands by name

Popular brands