manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 122

Troubleshooting

Service Manual

7-25

Samsung Electronics

Paper Jam (Mis-Feeding)

Sounds the 

solenoid on when starts 

print?

Does the 

paper move? 

Does the 

paper move more than 

100mm?

The Main PBA board defected 
-> Replace boards

The solenoid defected 
-> Replace it

The pick-up unit is 
assembled wrong 
-> Re-assemble or replace 
the unit

Feeder 

sensor is assembled 

reverse? 

Switch them

The sensor and 
Main PBA defected 
-> Repair/replace

Too many 

papers in the 

feeder?

Paper guides 

fit the paper width?

Paper end curled?

Does the 

extender pulled out?

<Recommendation>
Use the MPF for the thick 
paper such as envelope 
and cardstock

Reduce the amount 
and re-test

Take out the paper 
and re-insert

Use the recommended 
and quality paper

Pull out the 
extender

NO

NO

NO

NO

NO

NO

NO

YES

YES

YES

YES

YES

YES

YES

YES

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands