manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 103

Service Manual

Troubleshooting

7-6

Samsung Electronics

Poor Fusing

1. Use recommended paper?

2. Check fusing temperature.

3. The machine was under the low tempera ture

for a long time?

1. Should use recommended paper.

2. Check engine controller board. If you have

not thermometer, measure the thermistor
voltage to CPU, If 2.3V±5% in printing CPU
works well. Then, disassemble fuser and
check the thermistor contact and thermistor.

3. Re-check after putting the machine in the

warm place for certain period.

Error Status

Check

Solution

Partial blank image
(not periodic)

1. Toner is low?

2. The toner cartridge is out of position?

1. Replace Toner cartridge.

2. Checkand adjust.

Partial blank image
(periodic)

1. Develop roller scar or particle.

2. Scar or particle. (94.3 mm)

3. Transfer roller scar or particle. (56.6 mm)

1. Replace toner cartridge.

2. Replace drum cartridge.

3. Replace transfer roller.

Digital Printer

Digital Printer

Digital Printer

Digital Printer

Digital Printer

Digital Printer

Different image density
(left and right)

1. Charge roller’s pressure force unbalance

2. Dev. roller and OPC or Dev. roller and blade’s

pressure force unbalance

3. Transfer roller’s pressure force unbalance of

each side

1. Replace drum cartridge.

2. Replace toner cartridge and drum cartridge.

3. Check left and right spring of transfer roller

and the spring pressing the toner cartridge
inside the machine

Horizonral band

1. Unstable high voltage contact

2. Charge roller’s contamination

3. Contamination of heat roller

4. Malfunction of LSU

1. Clean each contact and check good contact

2. Clean charge roller

3. Replace fuser unit

4. Check Main PBA.

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands