manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 118

Troubleshooting

Service Manual

7-21

Samsung Electronics

7.4  Malfunction

No power

Fuser Error

Cover open

Jam 0

Jam 1

1. Check power is supplying

2. Check fuse F1 open

1. Thermostat open

2. AC wire open

3. Thermistor wire open

4. Main PBA

1. When close  Side cover, check the lever is

pressed

2. Micro switch’s contact

3. CPU and related circuit

Check where Jam 0 happens

1. Paper is not picked up

2. Paper is located in feed sensor

3. Happened when inserting specific papers such

as envelope into the MPF (Multipurpose Paper
Feeder)?

4. Happened when inserting specific papers such

as envelope into the Manual Feeder?

5. Is the Stacker Extender is folded out?

6. Does not the Guide Adjust distort the papers

Paper is stopped in just after of fuser unit.

1. If supplying power differs from machine’s

power rating, replace the machine.

2. Replace it.

1. Detach AC connector and measure the

resistane between pin 1 and 2. If it is
megohm, thermostat is open, Replace it.

2. Check bad connector contact or wire is cut.

3. Check thermistor wire and its connection.

4. Replace Main PBA

1. Open Side cover and press the lever with

pen. If  Controller detects cover close, there
is some mechanical trouble in Side cover
and lever’s assembly. If not so there is elec-
trical problem.

1. Check whether solenoid is working or not

by using Engine test mode

2. Check feed sensor malfunction.

3. Re-try inserting a fewer papers.

•fan the papers and align 

•take out the loaded papers and insert 

them reverse direction

4. Take out the loaded papers and insert them

reverse direction

•inserted papers as recommended for

Manual Feeding?

•When loading, tap the papers until paper

detect sensor senses loading

5. When using long papers, use the Stacker

Extender

6. Adjust Guide to fit the paper width

1. It is mostly resulted from double feeding.

Check paper is well stocked in feeder.

2. Check feed actuator position and actuator’s

operating. There may be stiff movind or
double reflection. If not so, check the opera-
tion of feed sensor by Engine test mode.

3. Check exit lever operation. Remore jam

and check actuator moving by hand. If actu-
ator is too stiff, paper is wrapped around the
heat roller. Remove obstacles or replace.

Error Status

Check

Solution

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands