manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 5

Samsung Electronics

Service Manual

Precautions

1-4

1.2.5 Disregarding this warning may cause bodily injury

(1) Take care - some parts may be hot.

The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cool
down before disassembly.

(2) Take care not to trap fingers or hair.

Take care when using a printer. It contains many rotating parts. Ensure that fingers, hair, clothing etc. do not
become caught in the mechanism as this could cause injury.

(3) When you move the printer.

This printer weighs 32kg including toner cartridge and cassette. Use safe lifting and handling techniques. Use
the lifting handles located on each side of the machine. Back injury could be caused if you do not lift carefully.

(4) Ensure the printer is installed safely.

The printer weighs 32Kg, ensure the printer is installed on a level surface, capable of supporting its weight.
Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.

(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands