manualshive.com logo in svg

Samsung SCX-6320F, Service Manual

Share
Download
Samsung SCX-6320F Service Manual Download Page 33

Summary of Product

Service Manual

4-11

Samsung Electronics

4.2.8.1.1 CRUM for Toner cartridge

Branded Samsung toner cartridges must be used in the SCX6220/6320F.

The Usage data saved in the CRUM are either used by other features or are printed on the billing / counters list.

Toner level gauge

- Toner Level has Normal, Low, and Empty states detected using a Toner sensor.

Note : The SCX-6320F does not support simulated toner gauge feature.

Usage data saved in CRUM

- Vendor (Vendor name)
- Capacity (Toner Cartridge Capacity)
- Product Date (Toner Cartridge production date)
- Install Date (Toner Cartridge installation date)
- Serial (Serial number)
- Total pages (Page count using this Cartridge)
- Toner Status (Toner Level : Normal, Low, Empty)

Non-Samsung cartridge

- Faulty CRUM: Stop printing

(UI: Invalid Cartridge)

- Non Samsung Cartridge: Stop printing
- Cartridge with inappropriate vendor ID: Stop printing
- Cartridge with different vendor ID from vendor ID of machine: Stop printing
“Invalid Cartridge” will be displayed on LCD in above 4 cases, and Copy/Fax/PC

job printing will be stopped (except printing Reports at “TECH MODE”)

CRUM Feature

Sub features

Summary of Contents for SCX-6320F

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands