manualshive.com logo in svg

Samsung S3C2416, User Manual

Share
Download
Samsung S3C2416 User Manual Download Page 554

LCD CONTROLLER  

 

S3C2416X RISC MICROPROCESSOR 

21-34  

 

8.1.3  Video Main Control 0 Register (Continued)

 

VIDCON0 

Bit 

Description 

Initial State

CLKVALUP 

[12] 

Select CLKVAL_F Update timing control 
0 = Always        
1 = Start of a frame (Only once per frame) 

0 

CLKVAL_F 

[11:6]  Determine the rates of VCLK.  

VCLK = (HCLK or LCD video Clock) / [1]   ( CLKVAL 

≥

 1 ) 

0 

VCLKEN 

[5] 

VCLK Enable Control 
0 = Disable 
1 = Enable 

0 

CLKDIR 

[4] 

Select the clock source as direct or divide using CLKVAL_F register. 
0 = Direct clock (frequency of VCLK = frequency of Clock source) 
1 = Divided using CLKVAL_F 

0 

CLKSEL_F 

[3:2] 

Select the Video Clock source 
00 = HCLK 
01 = LCD video Clock (from SYSCON EPLL) 
10 = Reserved 
11 = Reserved 

0 

ENVID 

[1:0] 

Video output and the LCD logics enable/disable control. 
00 = Disable video signals and logics immediately. 

01 = Reserved. 

10 = Disable video signals and logics at the end of current frame. 

11 = Enable video output and logics. 

Note :   If set to ‘10b’ in the middle of displaying current frame, the value of 
ENVID is still ‘11b’. However, the LCD functions are disabled at the end of 
current frame and the value is changed to ‘10b’.   

 

0 

 

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands