manualshive.com logo in svg

Samsung S3C2416, User Manual

Share
Download
Samsung S3C2416 User Manual Download Page 471

S3C2416X RISC MICROPROCESSOR 

 

HSMMC CONTROLLER 

  

20-25 

5.7 COMMAND REGISTER 

This register contains the SD Command Argument. 

Register 

Address 

R/W 

Description 

Reset Value

CMDREG0 0X4AC0000E  R/W Command Register (Channel 0) 

0x0 

CMDREG1 0X4A80000E  R/W Command 

Register (Channel 1) 

0x0 

 

The Host Driver shall check the 

Command Inhibit (DAT) 

bit and 

Command Inhibit (CMD) 

bit in the 

Present 

State 

register before writing to this register. Writing to the upper byte of this register triggers SD command 

generation. The Host Driver has the responsibility to write this register because the Host Controller does not 

protect for writing when 

Command Inhibit (CMD) 

is set. 

Name 

Bit 

Description 

Initial Value

 [15:14] 

Reserved

 

 

CMDIDX [13:8] 

Command Index 

These bits shall be set to the command number (CMD0-63, ACMD0-

63) that is specified in bits 45-40 of the Command-Format in the SD 

Memory Card Physical Layer Specification and SDIO Card 

Specification. 

 

 

CMDTYP [7:6] 

Command Type 

There are three types of special commands: Suspend, Resume and 

Abort. 
These bits 

shall 

be set to 00b for all other commands. 

•

  

Suspend Command 

If the Suspend command succeeds, the Host Controller shall assume 

the SD Bus has been released and that it is possible to issue the next 

command which uses the 

DAT 

line. The Host Controller shall de-assert 

Read Wait for read transactions and stop checking busy for write 

transactions. The interrupt cycle shall start, in 4-bit mode. If the 

Suspend command fails, the Host Controller shall maintain its current 

state, and the Host Driver shall restart the transfer by setting 

Continue 

Request 

in the 

Block Gap Control 

register.  

•  

Resume Command 

The Host Driver re-starts the data transfer by restoring the registers in 

the range of 000-00Dh. (Refer to Suspend and Resume mechanism) 

The Host Controller shall check for busy before starting write transfers. 

•  

Abort Command 

If this command is set when executing a read transfer, the Host 

Controller shall stop reads to the buffer. If this command is set when 

executing a write transfer, the Host Controller shall stop driving the 

DAT 

line. After issuing the Abort command, the Host Driver should 

issue a software reset. (Refer to Abort Transaction) 
11b = Abort CMD12, CMD52 for writing “I/O Abort” in CCCR 

10b = Resume CMD52 for writing “Function Select” in CCCR 

01b = Suspend CMD52 for writing “Bus Suspend” in CCCR 

00b = Normal Other commands

 

 

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands