manualshive.com logo in svg

Samsung S3C2416, User Manual

Share
Download
Samsung S3C2416 User Manual Download Page 401

S3C2416X RISC MICROPROCESSOR 

 

2D 

  

18-7 

4.1.8 Related 

Registers 

COORD_0 

Coordinate of the leftmost topmost coordinate of the source image 

COORD_1 

Coordinate of the rightmost bottommost coordinate of the source image 

COORD_2 

Coordinate of the leftmost topmost coordinate of the destination image 

COORD_3 

Coordinate of the rightmost bottommost coordinate of the destination image 

X-INCR 

X increment value of the source image coordinates. If it is greater than 1, the 

image is shrunk horizontally; smaller than 1, stretched. This value is ignored 

when S bit in CMDR_1 is disabled or host-to-screen mode is used.  
X-INCR = (COORD1_X 

−

 COORD0_X) / (COORD3_X 

−

 COORD2_X) 

Y-INCR 

Y increment value of the source image coordinates. If it is greater than 1, the 

image is shrunk vertically; smaller than 1, stretched. This value is ignored when S 

bit in CMDR_1 is disabled or host-to-screen mode is used. 
Y_INCR = (COORD1_Y 

−

 COORD0_Y) / ( COORD3_Y 

−

 COORD2_Y) 

SRC_BASE_ADDR 

The base address of the source image (when memory-to-screen mode is used).  

DEST_BASE_ADDR 

The base address of the destination image (usually the frame buffer base 

address) 

SRC_HORI_RES_REG 

The horizontal resolution of the source image 

SRC_VERT_RES_REG 

The vertical resolution of the source image (used in YUV mode) 

SC_HORI_RES_REG 

The screen resolution 

SRC_COLOR_MODE 

The color mode of the source image  

DEST_COLOR_MODE 

The color mode of the destination image 

BG_COLOR 

Background color, used in the Transparent Mode and Blue Screen Mode. 

BS_COLOR 

Blue screen color, used in the Blue Screen Mode. 

ROP_REG 

Enable/disable Transparent Mode or Blue Screen Mode. 

CMD1_REG 

Writing to this register starts the rendering process of memory-to-screen Bit Block 

Transfer. If S bit is set, the image will be shrunk or stretched, depending on the 

values of X-INCR and Y-INCR. 

CMD2_REG / CMD3_REG

The host provides the source image data through these two command registers. 

When the host writes the first 32-bit data into CMD2_REG, the rendering process 

starts in the host-to-screen mode. Then the host should provide the rest of data 

by writing into CMD3_REG continuously. Note that the data written to 

CMD2_REG/CMD3_REG each time represents only one pixel, regardless of the 

source color format. If the source color format is 16-bpp (e.g., RGB565), the 

upper 16 bits of the data are ignored. 

 

 

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands