manualshive.com logo in svg

Samsung S3C2416, User Manual

Share
Download
Samsung S3C2416 User Manual Download Page 546

LCD CONTROLLER  

 

S3C2416X RISC MICROPROCESSOR 

21-26  

 

4  VTIME CONTROLLER OPERATION 

4.1  RGB INTERFACE  

The VTIME generates the control signals such as, RGB_VSYNC, RGB_HSYNC, RGB_VDEN and RGB_VCLK 

signal for RGB interface. These control signals are highly related with the configuration on the VIDTCON0/1/2 

registers in the VSFR register. Base on these programmable configurations of the display control registers in 

VSFR, the VTIME module can generate the programmable control signals suitable for the support of many 

different types of display device.  

The RGB_VSYNC signal is asserted to cause the LCD's line pointer to start over at the top of the display. The 

RGB_VSYNC and RGB_HSYNC pulse generation is controlled by the configuration of both the HOZVAL field and 

the LINEVAL registers. The HOZVAL and LINEVAL can be determined by the size of the LCD panel according to 

the following equations: 

HOZVAL = (Horizontal display size) -1 

LINEVAL = (Vertical display size) –1

 

The rate of RGB_VCLK signal can be controlled by the CLKVAL field in the VIDCON0 register. The table below 

defines the relationship of RGB_VCLK and CLKVAL. The minimum value of CLKVAL is 1. 

RGB_VCLK (Hz) =HCLK/ [1] 

Table 21-5. Relation between VCLK and CLKVAL (Freq. of Video Clock Source=60MHz) 

CLKVAL 60MHz/X 

VCLK 

1 

60 MHz/2 

30.0 MHz 

2 

60 MHz/3 

15.0 MHz 

: : 

: 

63 

60 MHz/64 

938 kHz 

 

The RGB_HSYNC and RGB_VSYNC signal is configured by RGB_VSYNC, VBPD, VFPD, HSYNC, HBPD, 

HFPD, HOZVAL and LINEVAL. Refer the Figure 21-10. 

The frame rate is RGB_VSYNC signal frequency. The frame rate is related with the field of RGB_VSYNC, VBPD, 

VFPD, LINEVAL, HSYNC, HBPD, HFPD, HOZVAL, CLKVAL registers. Most LCD drivers need their own 

adequate frame rate. The frame rate is calculated as follows; 

Frame Rate = 1/ [ { (VSPW+1) + (VBPD+1) + (LI 1) + (VFPD+1) } x {(HSPW+1) + (HBPD +1) 
         + (HFPD+1) + ( 1) } x { (1 ) / ( Frequency of Clock source ) } ] 

 

4.2 i80-SYSTEM INTERFACE 

The VTIME generates the control signals such as, SYS_CS0, SYS_CS1, SYS_RS and SYS_WE signal for i80-

System Interface. The LCDIFMODE, LCD_CS_SETUP, LCD_WAIT_WR and LCD_HOLD_WR registers control 

these signals. Refer to figure 21-11.  

 

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands