manualshive.com logo in svg

Samsung S3C2416, User Manual

Share
Download
Samsung S3C2416 User Manual Download Page 142

STATIC MEMORY CONTROLLER 

 

S3C2416X RISC MICROPROCESSOR 

5-18 

 

 

Bit 

Description 

Initial State 

BurstLen 

Read 
 

[11:10] 

Burst transfer length. Sets the number of sequential transfers 

that the burst device supports for a read:  
00 = 4-transfer burst.     01 = 8-transfer burst.  

10 = 16-transfer burst.   11 = Reserved 

0x0 

SyncReadDev 
 

[9] 

Synchronous access capable device connected. Access the 

device using synchronous accesses for reads: 
0 = Asynchronous device (default). 

1 = Synchronous device. 

0x0 

BMRead 
 

[8] 

Burst mode read and asynchronous page mode:  
0 = Nonburst reads from memory devices (default at reset).  

1 = Burst mode reads from memory devices. 

0x0 

DRnCS [7] 

0 = No delay (defualt) 

1 = Get the delay between ADDR signal and nCS signal.   
The number of cycle is defined by DELAYnCS field of 

SMBCRx. 

This bit is applied only when nWAIT signal is used. 

0x0 

SMBLSPOL 
 

[6] 

Polarity of signal nBE:  
0 = Signal is active LOW (default).     

1 = Signal is active HIGH. 

0x0 

MW 
 

[5:4] 

Memory width:  
00 = 8-bit.                                       01 = 16-bit.  

10 = Reserved.                              11 = Reserved.  
Defaults to different values at reset for each bank. 
For SMBCR0, reset value is set according to OM. (See table 

1-4) 

See note in p5-

17 

Reserved [3] 

Reserved 

0x0 

WaitEn 
 

[2] 

External memory controller wait signal enable: 
0 = The SMC is not controlled by the external wait signal 

(default at reset).  

1 = The SMC looks for the external wait input signal, nWAIT. 

0x0 

WaitPol 
 

[1] 

Polarity of the external wait input for activation:  
0 = The nWAIT signal is active LOW (default at reset).  

1 = The nWAIT signal is active HIGH. 

0x0 

RBLE 
 

[0] 

Read byte lane enable:  
0 = nBE[1:0] all deasserted HIGH during system reads from 

external memory. This is for 8-bit devices where the byte lane 

enable is connected to the write enable pin so you must 

deassert it during a read (default at reset). The nBE signals 

act as write enables in this configuration.  
1 = nBE[1:0] all asserted LOW during system reads from 

external memory. This is for 16 or 32-bit devices where you 

use the separate write enable signal, and you must hold the 

byte lane selects asserted during a read. The nBE signal acts 

as the write enable in this configuration. 

0x0 

NOTE: 

Initial value of SMBCR0 is 0x303010 or 0x303000 according to OM value(See table 1-4), because the memory width,  
MW, of the booting memory is determined by OM. 

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands