manualshive.com logo in svg

Samsung S3C2416, User Manual

Share
Download
Samsung S3C2416 User Manual Download Page 451

S3C2416X RISC MICROPROCESSOR 

 

HSMMC CONTROLLER 

  

20-5 

4.3  SD CLOCK STOP SEQUENCE 

 

START

Set SD Clock OFF

END

(1)

Stop SD Clock

 

 

Figure 20-4. SD Clock Stop Sequence  

 

The flow chart for stopping the SD Clock is shown in Figure 20-4. The Host Driver shall not stop the SD Clock 

when a SD transaction is occurring on the SD Bus -- namely, when either Command Inhibit (DAT) or Command 

Inhibit (CMD) in the Present State register is set to 1. 

(1)  Set SD Clock Enable(ENSDCLK) in the Clock Control register to 0. Then, the Host Controller stops supplying 

the SD Clock. 

 

4.4  SD CLOCK FREQUENCY CHANGE SEQUENCE 

 

START

SD Clock Stop

SD Clock Supply

END

(1)

(2)

 

 

Figure 20-5. SD Clock Change Sequence  

The sequence for changing SD Clock frequency is shown in Figure 20-5. When SD Clock is still off, step (1) is 

omitted.  

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands