Samsung S3C2416 User Manual Download Page 30

Page: 30 / 672

PRODUCT OVERVIEW

S3C2416X RISC MICROPROCESSOR

1-2

2 FEATURES

2.1.1 Architecture

•

Integrated system for hand-held devices and

general embedded applications.

•

16/32-Bit RISC architecture and powerful

instruction set with ARM926EJ CPU core.

•

Enhanced ARM architecture MMU to support

WinCE, EPOC 32 and Linux.

•

Instruction cache, data cache, write buffer and

Physical address TAG RAM to reduce the effect

of main memory bandwidth and latency on

performance.

•

ARM926EJ CPU core supports the ARM debug

architecture.

•

Internal Advanced Microcontroller Bus

Architecture (AMBA) (AMBA2.0, AHB/APB).

2.1.2 System

Manager

•

Little/Big Endian support.

•

Two independent memory bus - one for the

ROM/SRAM bus (ROM Bank0~Bank5) and one

for the DRAM bus (mSDR/mDDR/DDR2

SDRAM Bank0~Bank1)

•

Address space: 64M bytes for Rom bank0 ~

bank5, 128M bytes for SDRAM bank0 ~ bank1.

•

Supports programmable 8/16-bit data bus width

for ROM/SRAM bank and programmable 16/32-

bit data bus width for SDRAM bank

•

Fixed bank start address from Rom bank 0 to

bank 5 and SDRAM bank 0 to bank1.

•

Eight memory banks:

– Six memory banks for ROM, SRAM, and

others (NAND etc.).

– Two memory banks for Synchronous DRAM.

•

Complete Programmable access cycles for all

memory banks.

•

Supports external wait signals to expand the bus

cycle.

•

Supports self-refresh mode in SDRAM for

power-down.

•

Supports various types of ROM for booting

(NOR Flash, EEPROM, OneNAND, IROM and

others).

2.1.3 NAND

Flash

•

Supports booting from NAND flash memory by

selecting OM as IROM boot mode. (Only 8bit

Nand and 8ECC is supported when it boots)

•

64KB for internal SRAM Buffer(8KB internal

buffer for booting)

•

Supports storage memory for NAND flash

memory after booting.

•

Supports Advanced NAND flash

2.1.4 Cache

Memory

•

64-way set-associative cache with I-Cache

(16KB) and D-Cache (16KB).

•

8words length per line with one valid bit and two

dirty bits per line.

•

Pseudo random or round robin replacement

algorithm.

•

Write-through or write-back cache operation to

update the main memory.

•

The write buffer can hold 16 words of data and

four addresses.

2.1.5 Clock & Power Manager

•

On-chip MPLL and EPLL:

EPLL generates the clock to operate USB Host,

IIS, UART, etc.

MPLL generates the clock to operate MCU at

maximum 400MHz @ 1.3 V.

•

Clock can be fed selectively to each function

block by software.

•

Power mode: Normal, Idle, Stop, Deep Stop and

Sleep mode

Normal mode: Normal operating mode

Idle mode: The clock for only CPU is stopped.

Stop mode: All clocks are stopped.

Deep Stop mode: CPU power is gated and all

clocks are stopped.

Sleep mode: The Core power including all

peripherals is shut down.

•

Woken up by EINT[15:0] or RTC alarm & tick

interrupt from Sleep mode and (Deep)STOP

mode.

Summary of Contents for S3C2416

































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for S3C2416

Reviews:

Brands by name

Popular brands

Samsung S3C2416, User Manual

Search results

Summary of Contents for S3C2416

Reviews:

Brands by name

Popular brands