Installation and operating manual: NEO/NEO-PS v.1.4S EN
(video camera) VIDEO signal. The module is equipped with JPG pictures quality regulation what enables sending
four pictures via single MMS, 100kB max. Triggering alarm action is done by: VIDEO detection, MGSM inputs
and outputs. The module enables saving a „frozen picture” onto SD card and its later reading via SMS order.
3.2.2 TSR-1: TMEPERATURE SENSOR
Digital temperature sensor with measurement range from -55°C to +125°C (+/- 1°C).
3.2.3 VSR-2 : VOICE SYNTHESIZER
This module is used to store and reproduce up to 16 radio announcements (8 x 16s + 8x 8s). It can be
additionally linked with an audio module for listening-in on objects. MSGM 4.0 enables independent summing of
messages coming from a number of recordings (5), in the event of violating/sabotaging the input.
3.2.4 VSR-1 : VOICE SYNTHESIZER
Module memorizes 20 second voice message.
3.2.5 AMR-1: AUDIO MODULE
The voice module is capable of replaying the object audio during the alarm or after establishing the
voice message. The module should be connected to the S-M input.
3.2.6 PSR-RF: THE BUFFERED POWER SUPPLY MODULE WITH TWO CHANNEL RADIO CONTROLLER
The extended PSR version with built in two channel radio controller for the remote control of NEO
(utilizing the control panel function). PSR-RF as an independent device can functionally replace any two channel
radio link and a buffered 13.8V DC/1.3A power supply.
4. INSTALLATION
The NEO/NEO-PS module should be installed indoors, where air humidity is normal (RH=90% max.
without condensation) and temperature in the range of -10°C
to
+45°C. When choosing place of installation the
following criteria should be taken into account:
- GSM network availability (of the SIM card operator utilized in the module),
- the availability and distance of alarm signal sources and trigger signals (e.g. the control panel),
- the availability of power supplies or installation possibility of such in vicinity,
- the MGSM 4.0 = 10V-14V/1A (min), buffered 13.8V DC power supplies
recommended (e.g. recommended dedicated PSR or PSR-RF)
- the MGSM 4.0-PS = 17V-20V/30VA, (the 17V-20V/AC terminals are used for
connection the secondary winding of mains transformer: O-R2/3, O-RH casings)
or DC power supplies recommended 20V-30V/1A min (e.g. PSU 24V DC)
- the availability of the premises to third parties and susceptibility to sabotage attempts,
- keeping safe distance from sources of potential interference (e.g. buildings, radio transmitters, etc. 230V AC
main power supply lines).
The NEO/NEO-PS+ module should be mounted in a dedicated metal housing:
- O-R1, O-R2, O-R3, O-R4, O-RH or other intended for GSM transmitter or control panel installation:
when installing the version without housing,
- information and communication systems via the DIN 35S bus: when installing the version with housing for the
DIN 35S bus (NEO/NEO-PSO-RDIN casing)
.
4.1. MODULE COMMISSIONNING PROCEDURE
1. The complete signaling and power supply wiring should be implemented.
2. Mount the housing and insert the wiring through the cable glands.
3. Install the SIM card in the module:
Insert the card in the SIMCARD socket in the vertical position, with the
golden contacts of the SIM card directed towards the closer edge of the
PCB board. The marker (cut-out) of the SIM card must be directed
opposite to the direction of inserting.
4. Install the module:
a) in the - O-R1, O-R2, O-R3, O-R4 housing on the pins included
in the kit,
b) in the GSM transmitter housings or control panel housing on
the self adhesive pins supplied with the module,
c) in the information and communication systems housing using
the clip securing the DIN
housing to the assembly bus.
5. Connect the optional additional modules: VSR-2, VSR-1, PSR, PSR-RF, FGR-4, AMR-1
6. Connect the wires to the appropriate module connectors.
6
