Installation and operating manual: NEO/NEO-PS v.1.4S EN
•
INSTANT
- the line initiates the alarm, SMS messages and calling when the module is in the
armed mode.
•
ARM/DISARM
- switching ARM/DISARM line, violation switches standby mode on, end of
violation switches it off. Line can operate also in the pulse mode (“pulsed line” option on) as
follows: first violation arms the module, the second violation disarms it and so on alternately.
The ARM/DISARM line can switch the SMS and voice signaling off when the option SIGNALLING
OFF is marked (signaling will be terminated when the module is disarmed, independently of the
signaling function progress!).
•
INTERIOR DELAYED
- the line triggers the alarm, text messaging (SMS) and calling after the
time for entry has expired and the armed mode has not been switched off, if the DELAYED
entry has been violated in the first place. Otherwise, it operates as a NORMAL entry.
The time for entry can be set in the OPTIONS tab.
•
COUNTING
– violation of this type of line will result in the incrementation of the violation
counter and when it reaches it’s value, it initiates the alarm procedures. The line is active in the
module standby mode (exactly like the NORMAL) and the violation counter is reset after a
certain time measured from the last violation.
e.g. for values as in the diagram, to initiate the alarm from the counter line, it should be violated 2 times at
intervals not longer than 60 seconds.
•
TIME
This parameter determines the time in ms (1s=1000ms), during which the input must be violated to
detect it’s change of state. For each input, the reaction time can be set independently (500 ms by
default). Min/max time= 250ms/60s.
•
FLASH
Determines whether the sent SMS message is to be displayed directly on the telephone screen (flash),
or whether it should be read from the “received mail” box. Selecting the option configures the input
SMS type for the “violation” and “entry restore”
REMARKS
:
●
it should be remembered that FLASH type SMS messages can be very easily overlooked,
because they are not recorded in the telephone (they disappear from the telephone
screen when there is an incoming call)
●
the FLASH option may not be available while sending SMS messages to a different
operator than the one whose card is in the module (this does not depend on the settings
but it is a result of limitations imposed by operators!).
●
Lock time
The time of blocking the input (response) after the first violation. This option is active for the following
TYPES of entry: INFO, NORMAL, DELAYED, INTERNAL DELAYED, 24H. The time of blocking can be set
separately for each entry (the default setting is 0s). Min/max time = 1/360min (this option is used for
limiting the number of messages and when using the NEO/NEO-PS as an alarm control panel; it enables
actual control of the armed mode through the SMS messages).
●
VSR message
This column enables configuring the content of voice messages, in cooperation with the
VSR-2 Voice Synthesizer.
Enter the characters corresponding to the numbers of registered voice messages and/or object sound
detectors:
- Messages: 0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F
(message maximum time: 0-7 = 16s; 8-F = 8s.)
- Audio module (microphone): m
It is possible to sum the content of message by entering a number of characters (no more
than 5), separated with a comma. The messages will be presented in a sequence, according
to the entry in the “m” tab. Each entry can be configured separately.
e.g. The sequence: 0,1,3,A
will make messages appear in “0, 1, 3, A” sequence, as one content.
e.g. The sequence: 0,1,3,5,m
will make messages appear in “0,1,3,5” sequence and activate the object sound (until the voice
connection is terminated by the user or the calling time has expired).
●
NIGHT
18
