manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 51

Configuring the I/O

4-15

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Downloading the Project to the Controller and Going Online

After adding the scanner and drive/adapter to the I/O configuration, you 
must download the configuration to the controller. You should also save 
the configuration to a file on your computer.

1. In the RSLogix 5000 window, select Communications > 

Download. The Download dialog box (

Figure 4.18

) appears.

Figure 4.18 Download Dialog Box  

2. Click Download to download the configuration to the controller. 

When the download is successfully completed, RSLogix 5000 goes 
into the Online mode and the I/O OK box in the upper-left of the 
screen should be solid green.

3. Select File > Save. If this is the first time you saved the project, the 

Save As dialog box appears. Navigate to a folder, type a file name, 
and click Save to save the configuration to a file on your computer.

4. To ensure that the present project configuration values are saved, 

RSLogix 5000 prompts you to upload them. Click Yes to upload 
and save them.

5. Place the controller in Remote Run or Run Mode.

TIP:  If a message box reports that RSLogix 5000 is unable to go 
online, select Communications > Who Active to try to find your 
controller in the Who Active screen. After finding and selecting the 
controller, click Set Project Path to establish the path. If your 
controller does not appear, you need to add or configure the 
DeviceNet driver in RSLinx. Refer to the RSLinx online help.

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands