Rockwell Automation PowerFlex 750-Series User Manual Download Page 11

Page: 11 / 144

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Chapter

Getting Started

The 20-750-DNET Option Module is intended for installation into a
PowerFlex 750-Series drive and is used for network communication.

Components

Figure 1.1

Components of the Option Module

Topic

Page

Item Part

Description

➊

Status
Indicators

Three LEDs that indicate the status of the Option Module and network
communications. Refer to

Chapter 7

Troubleshooting

➋

Data Rate
Switch

Sets the DeviceNet data rate at which the Option Module
communicates. Refer to

Setting the Data Rate Switch on page 2-3

➌

Node Address
Switches

Sets the node address of the Option Module. Refer to

Setting the Node

Address Switches on page 2-2

➍

DeviceNet
Connector

A 5-pin connector to which a 5-pin linear plug (supplied with DeviceNet
Option Module) can be connected to the DeviceNet cable.

➊

➋

➌

➍

Summary of Contents for PowerFlex 750-Series

















































































































































Search results

Summary of Contents for PowerFlex 750-Series

Reviews:

Brands by name

Popular brands

Rockwell Automation PowerFlex 750-Series, User Manual

Search results

Summary of Contents for PowerFlex 750-Series

Reviews:

Brands by name

Popular brands