manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 48

4-12

Configuring the I/O

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

– Output Size: Multiply the number of Datalinks used to read data 

(value of Device Parameter 04 - [DLs To Net Cfg]) by 4 bytes, 
and add this result to the minimum 8 bytes. For example, if 
Parameter 04 has a value of “7,” add 28 bytes (7 x 4 bytes) to 
the required minimum 8 bytes for a total of 36 bytes.

11. Set the scan rate for the selected data exchange method. (For more 

information about scan rates, refer to RSNetWorx for DeviceNet 
online help.)  

12. Click OK. If a Scanner Configuration Applet appears, click Yes to 

continue. The Edit I/O Parameters screen closes and then the 
1756-DNB Scanlist tab screen (

Figure 4.14

) reappears.

13. Click the Input tab to display the input registers for the 1756-DNB. 

Click AutoMap to map the drive input image to the 1756-DNB as 
shown in 

Figure 4.16

.  

Figure 4.16 1756-DNB Input Tab Screen  

14. Click the Output tab to display the output registers for the 

1756-DNB. Click AutoMap to map the drive output image to the 
1756-DNB as shown in 

Figure 4.17

.  

Data Exchange Method

Rate Field to Set

Polled

Poll Rate

Change of State

Heartbeat Rate

Cyclic

Send Rate

TIP:  If your RSLogix 5000 project requires a different starting 
DWord (double word, 32-bit) than the default value of 0 for the 
drive input image, set the Start DWord field to the appropriate value.

TIP:  If your RSLogix 5000 project requires a different starting 
DWord (double word, 32-bit) than the default value of 0 for the drive 
output image, set the Start DWord field to the appropriate value.

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands