manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 22

2-6

Installing the Option Module

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Table 2.A Drive and Option Module Start-Up Status Indications  

After verifying correct operation, swing down the drive HIM bezel to its 
closed position and install the drive cover.

Configuring/Verifying Key Drive Parameters

The PowerFlex 750-Series drive can be separately configured for the 
control and Reference functions in various combinations.  For example, 
you could set the drive to have its control come from a peripheral or 
terminal block with the Reference coming from the network.  Or you 
could set the drive to have its control come from the network with the 
Reference coming from another peripheral or terminal block.  Or you 
could set the drive to have both its control and Reference come from the 
network.

Item Name

Color

State

Description

Drive STS Indicator

➊

STS 
(Status)

Green

Flashing

Drive ready but not running, and no faults 
are present.

Steady

Drive running, no faults are present.

Yellow

Flashing

When running, a type 2 (non-configurable) 
alarm condition exists – drive continues to 
run. When stopped, a start inhibit condition 
exists and the drive cannot be started (see 
drive parameter 933 - [Start Inhibits]).

Steady

A type 1 (user configurable) alarm condition 
exists, but the drive continues to run.

Red

Flashing

A major fault has occurred. Drive will stop. 
Drive cannot be started until fault condition 
is cleared.

Steady

A non-resettable fault has occurred.

Red/Yellow

Flashing Alternately A minor fault has occurred. Use drive 

parameter 950 - [Minor Flt Config] to enable. 
If not enabled, acts like a major fault. When 
running, the drive continues to run. System 
is brought to a stop under system control. 
The fault must be cleared to continue.

Yellow/Green Flashing Alternately When running, a type 1 alarm exists.
Green/Red

Flashing Alternately Drive is flash updating.

Option Module Status Indicators

➋

PORT

Green

Flashing

Normal Operation. The Option Module is 
establishing an I/O connection to the drive. 
It will turn solid green or red.

Steady

Normal Operation. The Option Module is 
properly connected and communicating 
with the drive.

➌

MOD

Green

Flashing

Normal Operation. The Option Module is 
operating but is not transferring I/O data.

Steady

Normal Operation. The Option Module is 
operating and transferring I/O data.

➍

NET A

Green

Flashing

Normal Operation. The Option Module is 
properly connected but is not 
communicating with any devices on the 
network.

Steady

Normal Operation. The Option Module is 
properly connected and communicating on 
the network.

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands