manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 26

3-2

Configuring the Option Module

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Using the HIM to Access 
Parameters in the Option 
Module

1. Display the Status screen, which is shown on HIM power up.

2. Use the 

 or 

 key to scroll to the Port in which the 

DeviceNet Option Module is installed.

3. Press the PAR# soft key to display the Jump to Param # entry 

pop-up box.

4. Use the numeric keys to enter the desired parameter number, or use 

the 

S

 or 

T

 soft key to scroll to the desired parameter number.

Setting the Node Address

If the Data Rate switch (

Figure 2.2

) is set to position “3,” the value of 

Device Parameter 07 - [Net Addr Cfg] determines the node address. 
When the Data Rate switch is set to any other position, the Node 
Address switches determine the node address. We recommend that you 
do not use node address 63 because all new devices on the network use 
this address as the default address. Also, node address 63 is used for 
Automatic Device Recovery (ADR).

1. Set the value of Device Parameter 07 - [Net Addr Cfg] to a unique 

node address.

Figure 3.1

Edit Net Address Cfg HIM Screen  

2. Reset the Option Module; see 

Resetting the Option Module on 

page 3-8

.

The NET A status indicator will be solid green or flashing green if 
the node address is correctly configured, and the Option Module is 
connected to an operational network.

Setting the Data Rate

If the Option Module Data Rate switch (

Figure 2.2

) is set to position 

“3” (Program), the value of Device Parameter 09 - [Net Rate Cfg] 
determines the data rate. The Autobaud setting will detect the data rate 
used on the network if another device is setting the data rate. Your 
application may require a different setting.

1. Set the value of Device Parameter 09 - [Net Rate Cfg] to the data 

rate at which your network is operating.

ESC

ENTER

Stopped
0.00 Hz

AUTO

F

Edit Net Addr Cfg

63

0 << 63

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands