manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 38

4-2

Configuring the I/O

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

5. When the Add New RSLinx Driver screen appears, type a name (if 

desired) and click OK. The Configure Drivers screen reappears 
with the new driver in the Configured Drivers list (

Figure 4.1

).

Figure 4.1

Configure Drivers Screen with a Configured Driver  

6. Click Close to close the Configure Drivers screen. Leave RSLinx 

running.

ControlLogix Example

Example Network

After the Option Module is configured, the connected drive and Option 
Module will be a single node on the network. This section provides the 
steps needed to configure a simple DeviceNet network (see 

Figure 4.2

). 

In our example, we will configure a ControlLogix controller with 
1756-DNB scanner to communicate with a drive using Logic 
Command/Status, Reference/Feedback, and 32 Datalinks (16 to read/16 
to write) over the network.

Figure 4.2

Example ControlLogix DeviceNet Network  

Adding the Scanner to the I/O Configuration

To establish communications between the controller and Option 
Module over the network, you must first add the ControlLogix 
controller and its scanner to the I/O configuration.

Node 0

ControlLogix Controller 

with 1756-DNB Scanner

Node 1

PowerFlex 750-Series 

Drive with 20-750-DNET 

Option Module

Node 62

Computer with 

DeviceNet Connection

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands