manualshive.com logo in svg

Rockwell Automation PowerFlex 750-Series, User Manual

Share
Download
Rockwell Automation PowerFlex 750-Series User Manual Download Page 45

Configuring the I/O

4-9

 

 

 

PowerFlex 750-Series Drive DeviceNet Option Module User Manual

Publication 750COM-UM002A-EN-P

Figure 4.12 1756-DNB Properties Screen  

7. Click the Module tab to display the Scanner Configuration Applet 

screen. Click Upload to upload the 1756-DNB configuration to the 
RSNetWorx for DeviceNet project and display the 1756-DNB 
Module Tab screen (

Figure 4.13

).

Figure 4.13 1756-DNB Module Tab Screen  

8. Edit the following:  

Then click Apply.

Box

Setting

Interscan Delay Sets the scanner time delay between consecutive I/O scans on the 

network. For this example, it is recommended to leave the default setting 
of 10 milliseconds. Note: When numerous drives are on the network and 
the drives are faulting on a Comm Loss, increasing this value may help.

Foreground…

Sets the ratio of foreground to background polls. For this example, it is 
recommended to leave the default setting of 2.

Slot

Sets the slot location in which the scanner is installed. For this example, 
Slot 3 is selected.

Summary of Contents for PowerFlex 750-Series

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands