Programming and Parameters
3-115
PowerFlex 700S Phase II AC Drive User Manual -
Publication 20D-UM006G-EN-P – July 2008
1143
PPMP Pos Output
Provides a position reference output from the Motion Planner. This output is scaled in counts.
Typically this parameter would be used by the drive's Position Loop. A link could be made from
auxiliary position input to this parameter.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0.0
-/+ 2147483648.0
RO Real
1144
PPMP Pos To Go
Provides indication of feedback counts remaining in the move.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0.0
-/+ 2147483648.0
RO Real
1145
PPMP TP Select
Motion Planner test point selection.
Notes: This parameter was added for firmware version 3.01. Selection 9 was changed to
“Reserved” for firmware version 4.001.
Default:
Options:
0 =
0 =
1 =
2 =
3 =
4 =
5 =
6 =
7 =
8 =
9 =
10 =
11 =
12 =
13 =
14 =
15 =
16 =
“Zero”
“Zero”
17 = “MP Mtn Calc”
“MP FrctAccmI”
18 = “MP AnlgPulse”
“MP WholeAccm”
19 = “MP Rate In”
“MP EPR”
20 = “MP Rate Out”
“MP NBase”
21 = “MP Gain”
“MP Once Flag”
22 = “MP Kx”
“MP Pos Fdbk”
23 = “MP FrctAccmR”
“MP Pos Fdbk1”
24 = “MP AccelRate”
“MP ErrorSum”
25 = “MP DecelRate”
“Reserved”
26 = “MP Cal”
“MP IntegHold”
27 = “SC Sum”
“MP Pos Exact”
28 = “SC Index”
“MP Pos Diff”
29 = “SC ArraySize”
“MP One Shot”
30 = “SC Once”
“MP Run Delay”
31 = “SC Enable”
“MP ResyncOne”
32 = “SC Ipos”
“MP Task Time”
1146
PPMP TP DataDInt
Test point integer data. This data is meaningful only if the selection at
[PPMP TP
Select] is integer data.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0.0
-/+ 2147483648.0
RO 32-bit
Integer
1147
PPMP TP DataReal
Test point real data. This data is meaningful only if the selection at
[PPMP TP
Select] is not integer data.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0.0
-/+2200000000.0
RO Real
1150
DInt2Real2 In
Input value for a second DInt to Real value conversion.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0
-/+2147483648.0
✓
RW 32-bit
Integer
1151
DInt2Real2 Scale
Input value to scale the second conversion from DInt to Real. This is a multiplication to the
input value after conversion to a Real value.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0.0
-/+2200000000.0
✓
RW Real
1152
DInt2Real2Result
This is the resultant output of the second conversion form a DInt value to a Real value after
scaling.
Note: This parameter was added for firmware version 3.01.
Default:
Min/Max:
0.0
-/+2200000000.0
RO Real
1155
Heidn VM Pos Ref
Virtual Master position reference for the Heidenhain option card. This value is used by the
Virtual Master function as a position reference. This parameter can be linked to a position
reference source, such as
[VirtEncPositFast].
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
✓
RW 32-bit
Integer
1156
Heidn VM Enc PPR
Virtual Master Encoder Pulse per Revolution (PPR). This value defines the encoder PPR for
the Virtual Master function. The Heidenhain option card produces the encoder pulse
according to this PPR value, which is limited to 1024 or 2048 encoder lines.
Note: This parameter was added for firmware version 4.001.
Units:
Default:
Min/Max:
PPR
1024
1024 and 2048 only
RW 32-bit
Integer
1160
VirtEncPositFast
Virtual Encoder position output in Task 1. One of three outputs from the Virtual Encoder
function. This value is the encoder position reference output for Task1 (fast rate).
[Virt
[Virt Encdr Dlyed] are the encoder position output in Task 2. For the
Virtual Master Encoder function, you must use Par 1160 [VirEncPosiFast] as the position
reference updated in Task 1.
Note: This parameter was added for firmware version 4.001.
Default:
Min/Max:
0.0
-/+2147483648.0
RO 32-bit
Integer
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype
