Rockwell Automation PowerFlex 700S, User Manual

Page: 120 / 318

3-62 Programming and Parameters
PowerFlex 700S Phase II AC Drive User Manual - Publication 20D-UM006G-EN-P – July 2008
412 Power EE TP Sel
Enter or write a value to select drive power EEPROM data displayed in Par 413 [Power EE TP Data]. The default is 0 “Zero”.
Note: Options 74 - 92 were changed and options 93 - 111 were added for firmware version 3.01.
413 Power EE TP Data
Displays the data selected by Par 412 [Power EE TP Sel].
Default:
Min/Max: 0
-/+2200000000 RO Real
414 Brake/Bus Cnfg
Configures the brake and bus operation of the drive.
•
Set bit 0 “Brake Enable” to enable the operation of the internal brake transistor.
•
Set bit 1 “Brake Extern” to configure the brake to use an external resistor.
•
Set bit 2 “Bus Ref High” to select the "high" voltage setting as the turn-on point for the Bus Voltage Regulator. With the "high" setting brake operation starts
when bus voltage reaches the value of
Par 415 [BusReg/Brake Ref], and Bus Voltage Regulator operation starts when bus voltage reaches the value of Par
415 [BusReg/Brake Ref] plus 4.5%. With the "low" setting, the bus regulator turns on first at the value set by Par 415 [BusReg/Brake Ref] and then the
dynamic braking turns on when there are any transients above the value set in Par 415 [BusReg/Brake Ref].
•
Set bit 3 “Bus Reg En” to enable the Bus Voltage Regulator. The output of the Bus Voltage Regulator is summed with Par 128 [Regen Power Lim] and fed into
the Power Limit Calculator. It, in effect, reduces regenerative torque references when the bus voltage is too high.
Notes: This parameter was changed to non-linkable and bits 5 and 6 were added for future use - not active for use with firmware version 3.01. Remove bits 5 and
6 for firmware version 4.001 - not used.
415 BusReg/Brake Ref
Sets the “turn-on” voltage for the bus regulator and brakes. Enter a percentage of the high
voltage setting for the voltage class. For example, on a 400-480V drive,
Note: The minimum value for frame 5 and up, 600V AC input drives was changed from
110.5000 to 100.0000 for firmware version 4.002.
(1) The minimum value is 100.0000 for frame 5 and up, 600V AC input drives.
Units:
Default:
Min/Max: %
111.0000
110.5000
(1)
/117.8000
RW Real
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype
Options:
0 = Zero 19 = Bus VltScale 38 = IGBT Rated A 61 = Convt Type 80 = HH1 P/B ID 99 = HH2 P/B ID
1 = Volt Class 20 = Sml PS Watts 39 = IGBT V Thres 62 = DC Bus Induc 81 = HH1 S/W ID 100 = HH2 S/W ID
2 = Assy Rev 21 = Sml PS Min V 40 = IGBT Slope R 63 = AC Inp Induc 82 = HH1 P/B Rev 101 = HH2 P/B Rev
3 = ASA S/N 22 = Lrg PS Watts 41 = IGBT Sw Engy 64 = Precharg Res 83 = HH1 S/W Rev 102 = HH2 S/W Rev
4 = Manuf Year 23 = Lrg PS Min V 44 = IGBT CS Tres 65 = PrechThrm Tc 84 = HH1 Extr Data 103 = HH2 ExtrData
5 = Manuf Month 24 = Inv Rated Kw 45 = IGBT CS Tc 66 = Mtr NP Units 85 = HH1 VoltIndx 104 = HH2 VoltIndx
6 = Manuf Day 25 = Inv Rated V 46 = Diode V Thrs 67 = Mtr NP Power 86 = HH1 SizeIndx 105 = HH2 SizeIndx
7 = Tst ProcStat 26 = Inv Rated A 47 = Diode SlopeR 68 = Mtr NP Volts 87 = HH1 Option 106 = HH2 Option
8 = Life PwrCycl 27 = Inv 1min Amp 48 = Diode JC Tr 69 = Mtr NP Amps 88 = HH1 HrdPrdct 107 = HH2 HrdPrdct
9 = Life Pwrup 28 = inv 3sec Amp 49 = Diode JC Tc 70 = Mtr NP Freq 89 = HH1 H/W Mdfy 108 = HH2 H/W Mdfy
10 = Life RunTime 29 = SW OverC Amp 50 = GBT Tjmax 71 = Mtr NP RPM 90 = HH1 1V/Amp 109 = HH2 1V/Amp
11 = Kw Accum 30 = DC Bus Cap 51 = HS Max DegC 72 = Mtr IR Vdrop 91 = HH1 2s/Amp 110 = HH2 2s/Amp
12 = Mw Hrs Accum 31 = Min PWM Khz 52 = DB IGBT Amp 73 = Mtr Id Ref 92 = HH1 Scale 111 = HH2 Scale
13 = Inv High Vlt 32 = Max PWM Khz 53 = DB ohms 74 = HH1 Data Rev 93 = HH2 Data Rev
14 = Reserved 33 = Dfl PWM Khz 54 = DB E Jo/degC 75 = HH1 Dev Type 94 = HH2 Dev Type
15 = Fan/Pwr Cntl 34 = PWM Dead us 55 = DB EB C/Watt 76 = HH1 Serial # 95 = HH2 Serial #
16 = Temp Sensor 35 = Drive Frame 56 = DB B Jo/degC 77 = HH1 Test Date 96 = HH2 TestDate
17 = Phs AmpScale 36 = IGBTs per Pk 57 = DB BA C/Watt 78 = HH1 Vcn Code 97 = HH2 Vcn Code
18 = Gnd AmpScale 37 = GBT Rated V 60 = DB Ambt Tmax 79 = HH1 CrsCncID 98 = HH2 CrsCncID
Options
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Res
er
ve
d
Bus
Re
g
En
Bus
Re
f High
Br
ak
e Ex
ter
n
Br
ak
e Ena
ble
Default 0 0 1 1 0 0 0 0 0 0 0 0 1 1 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 = False
1 = True
111 2
×
480 VDC
=
×