Rockwell Automation PowerFlex 700S, User Manual

Page: 101 / 318

Programming and Parameters 3-43
PowerFlex 700S Phase II AC Drive User Manual - Publication 20D-UM006G-EN-P – July 2008
269 Resolver0 Status
Indicates status of the resolver option card port 0.
•
Bit 0 “-Cable Tune”
•
Bit 1 “-Tune Result” indicates the tuning Parameter type. When set, it indicates the tuning is using the parameter database. When cleared, it indicates the tuning
is using derived data.
•
Bit 2 “-Mtr Turning” indicates that the motor is turning.
•
Bit 4 “Energized” indicates the resolver is energized.
•
Bit 8 “Open Wire” indicates a problem with the cable (open circuit).
•
Bit 9 “Power Supply” indicates problem with the option card's power supply.
•
Bit 10 “Diag Fail” indicates the option card has failed its power-up diagnostics.
270 Reslvr0 TP Sel
Enter or write a value to select Fault data displayed in Par 271 [Reslvr0 TP Data].
Default:
Options: 0 =
0 =
1 =
2 =
3 = “Zero”
“Zero”
4 = “R0 EPR”
“R0 Edge Time” 5 = “R0 Edge Mode”
“R0 dEdge” 6 = “R0 nMax”
“R0 dTime” 7 = “R0 Delta2Err”
271 Reslvr0 TP Data
Displays the data selected by Par 270 [Reslvr0 TP Sel].
Default:
Min/Max: 0
-/+2147483648 RO 32-bit
Integer
272 Reslvr0 SpdRatio
Specifies the speed ratio for the resolver option card port 0. The speed ratio comes from the
following formula. Speed ratio = electrical revolutions / mechanical revolutions = pole count /
2.
Note: Option 0 = “Zero” was added for firmware version 2.04.
Default:
Options: 1 =
0 =
1 =
2 = 2 poles (x1)
“Zero”
3 = 6 Poles (x3)
2 Poles (x1) 4 = 8 Poles (x4)
4 Poles (x2) 5 = 10 Poles(x5)
273 Reslvr0 Carrier
Specifies the resolver carrier frequency for the resolver option card port 0.
Units:
Default:
Min/Max: Hz
0
0/10000 RO 32-bit
Integer
274 Reslvr0 In Volts
Specifies the resolver input voltage for the resolver option card port 0.
Units:
Default:
Min/Max: Volt
0.0000
0.0000/31.0810 RO Real
275 Rslvr0 XfrmRatio
Specifies the resolver transform ratio for the resolver option card port 0.
Default:
Min/Max: 0.0000
0.0000/4.0950 RO Real
276 Reslvr0 CableBal
Specifies the resolver cable balance for the resolver option card port 0.
Default:
Min/Max: 0
0/255 RO Real
277 Reslvr0 Type Sel
Specifies used resolver.
The values for options 5 & 12 were changed to “Reserved” for firmware version 2.04. Added
options 15 and 16 for firmware version 4.001 but are not functional (for future use).
Default:
Options: 0 =
0 =
1 =
2 =
3 =
4 =
5 =
6 =
7 =
8 = “Disabled”
“Disabled”
9 = “1326Ax 460v”
“T2014/2087x1” 10 = “Reserved”
“T2014/2087x2” 11 = “Reserved”
“T2014/2087x5” 12 = “Reserved”
“MPL 460v” 13 = “Reserved”
“Reserved” 14 = “AmciR11XC107”
“Siemens 1FT6” 15 = “PowerTec R1”
“PrkrHn ZX600” 16 = “PowerTec R2”
“Reserved”
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype
Options
Res
er
ved
Res
er
ved
Res
er
ved
Res
er
ved
Selec
t OK
Diag F
ail
P
ow
er
Supply
Open
Wir
e
Res
er
ved
Res
er
ved
Res
er
ved
Ene
rgiz
ed
-Ca
ble
Co
mp
-M
tr
T
ur
ni
ng
-T
une Res
ult
-C
ab
le T
une
Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 = False
1 = True