Select menus
F X - 4 0
25
12.3 MODEL MENU (FIXED-WING AIRCRAFT)
This menu contains the settings specific to each model type for each
model memory, especially mixer functions. The Select menu varies
according to the model type you have selected:
Servo Monitor
= Servo travel display
Condition Select
= Flight mode select
AFR (D/R)
= Transmitter control travel settings, Dual Rates
Prog. Mixes
= Ten freely programmable mixers
AIL Differential
= Aileron differential
Flap Setting
= Mixer setting, brake -> flap
AIL to Camber FLP
= Aileron -> flap mixer
AIL to Brake FLP
= Aileron -> brake flap mixer
AIL to RUD
= Aileron -> rudder mixer
Airbrake to ELE
= Airbrake -> elevator mixer
Camber Mix
= Flap -> brake flap mixer
ELE to Camber
= Elevator -> flap / brake flap mixer
Camber FLP to ELE
= Flap / brake flap -> elevator mixer
RUD to Ail
= Rudder-> aileron mixer
RUD to ELE
= Rudder -> elevator mixer
Snap Roll
= Snap roll settings
Butterfly
= Butterfly (Crow) settings
Gyro
= Gyro settings
Fuel Mixture
= Carburator mixture adjust
Multi Engine
= Mixer for multi-engine models
Trim mix 1 + 2
= Trim mixers 1 + 2
Motor
= Motor settings
V-tail
= V-tail mixer
Ailevator
= Separate elevators (aileron function)
Winglet
= Winglet mixer, flying wings
MODEL MENU (HELICOPTER)
Servo monitor
= Servo travel display
Condition Select
= Flight mode select
AFR (D/R)
= Transmitter control travel settings, Dual Rates
Prog. Mixes
= Ten freely programmable mixers
PIT Curve
= Collective pitch curve settings
THR Curve
= Throttle curve settings
Acceleration
= Acceleration, throttle / coll. pitch function
Throttle Hold
= Auto-rotation settings
Swash Mix
= Swashplate mixer
Throttle Mix
= Throttle mixer
PIT to Needle
= Coll. pitch -> needle valve mixer
PIT to RUD
= REVO mix (tail rotor mixer)
Fuel Mixture
= Carburator mixture settings
Gyro
= Gyro mixer
Governor
= RPM governor (regulator)
12. SUMMARY OF SELECT MENUS
12.1 SYSTEM MENU
This menu is used to adjust transmitter settings which apply to
all models, i.e. they are non model memory-specific.
Trainer
= Trainer mode settings
Display
= Contrast / backlighting, transmitter power-off
Date / Time
= Calendar, date and time settings
User name
= User name and PIN
Switch
= Switch type and position settings
HW/Setting
= Hardware transmitter control reverse
Primary stick response time and dead-
band
Stick mode select, throttle left / right
Information
= Software version, memory capacity and
language switch (German / English)
12.2 Linkage MENU
This is where all the model’s basic settings are adjusted, and
picture and sound files are linked to each model memory.
Servo Monitor
= Servo travel display
Model Select
= Model memory select
Model Type
= Model type select
Picture
= Picture link
Sound
= Speech output link
Frequency
= Frequency / modulation select
Function
= Transmitter control select,
channel sequence
Sub-Trim
= Servo centre offset
Servo Reverse
= Servo travel direction reverse
Fail Safe
= Servo position if signal fails
End-Point (ATV)
= Servo travel adjust
Throttle Cut
= Motor cut function
Idle Down
= Second throttle idle position
Timer
= Stopwatch adjust
Dial Monitor
= Display of trimmer / adjustor
positions
Data Reset
= Reset data
The menu for the Helicopter model type with electronic swash-
plate mixing (HR3, H4) also includes a Swashplate menu,
(swash) where you can define the neutral point of the collecti-
ve pitch function and set the swashplate travel.
