background image

3 Top Edge

The top edge of the book.

4 Fore Edge

The front edge of the book; the edge of the signature opposite the spine. This
is edge of the book that the reader opens.

5 Bottom Edge

The bottom edge of the book.

6 Cover

Covers the pages (signature) of the book. The cover and signature are glued
at the spine.

NOTE: The top, bottom, and fore edges of the book are trimmed in the trimming unit after the signature
has been glued to the cover.

Warnings, Cautions, Notes

In this manual, the following important symbols and notations are used.

• A Warning indicates a potentially hazardous situation. Failure to obey a Warning could result in

death or serious injury.

• A Caution indicates a potentially hazardous situation. Failure to obey a Caution could result in minor

or moderate injury or damage to the finisher or other property.

• Obey these guidelines to avoid problems such as misfeeds, damage to originals, loss of valuable

data and to prevent damage to the finisher.

• This information provides tips and advice about how to best service the finisher.

General Safety Instructions

For your safety, please read this manual carefully before you use this product. Keep this manual handy for
future reference.
Safety Information
Always obey the following safety precautions when using this product.
Safety During Operation
In this manual, the following important symbols and notations are used.
Switches and Symbols

3

Summary of Contents for D391











































































































































































































































































































































































































































































































Reviews: