
SW1
1
2
3
4
Up
*
*
*
2. Set the SW2 bank as shown below.
SW2
1
2
3
4
5
6
7
8
*
Up
Up
*
*
Up
Up
*
3. Push [PSW1] then look at LED1, LED2, LED3 to read the current temperature setting.
• To raise the temperature, adjust in the plus (+) direction.
• To lower the temperature, adjust in the minus (-) direction.
4. Push [PSW2] to raise the current temperature setting by "1".
-or-
Push [PSW3] to lower the current temperature setting by "1".
5. LED1, LED2, LED3 light for 300 ms.
6. Look at LED1, LED2, LED3 to read the new temperature setting.
7. Repeat the steps above if you want to change the value again.
8. Push [PSW1] to write the new temperature setting into the EEPROM and shift to adjustment mode
standby.
LED1 flashes at 1 sec. intervals, LED2, LED3 go OFF.
Adjustment Range
Adjustment Range
Steps
Default
151°C to 155°C
(303.8°F to 311°F)
1
153
9. Read the current setting from the LED display. (See "How to Read the LEDs".)
• The LED2 count indicates the left digit (10's) of the 2-digit decimal value, the LED3 count indicates
the right digit (1's) of the 2-digit decimal value. Flash duration: 300 ms
• For example, if LED2 flashes 5 times and LED3 flashes 5 times, this means the value is 153°C
((10 x 5)+(1 x 3) +100) and the current temperature is set for 153°C.
• The LEDs remain OFF for 2 sec. if the current value is "0".
• The LED2 and LED3 displays automatically alternate.
Example 1: Current Temperature 153C
4. Troubleshooting
342
4
Summary of Contents for D391
