Ricoh Aficio MP 2500 Facsimile Reference Manual Download

Page: 194 / 204

Appendix

184

❖

IP-Fax Transmission and Reception

❖

Internet Fax Transmission and Reception

Full mode

Network

LAN: Local Area Network

Ethernet/10base-T, 100base-TX, IEEE802.11b (wireless LAN)

Scan line density

3.85/mm, 200

100 dpi (Standard character),

7.7/mm, 200

200 dpi (Detail character),

15.4/mm (Fine character)

Maximum original size

Standard size: A3

, 11"

17"

Custom size: 297

1200 mm, 11"

47"

Maximum scanning size

297

1200 mm, 11"

47"

Transmission protocol

Recommendation: T.38, TCP, UDP/IP communication, SIP
(RFC 3261 compliant), H.323 v2

Compatible machines

IP-Fax compatible machines

IP-Fax transmission function

Specify an IPv4 address and send faxes to an IP-Fax compati-
ble fax through a network.

Also capable of sending faxes to a G3 fax connected to a tele-
phone line via a VoIP gateway.

IP-Fax reception function

Receive faxes sent from an IP-Fax compatible fax through a
network.

Also capable of receiving faxes from a G3 fax connected to a
telephone line via a VoIP gateway.

Network

LAN : Local Area Network

Ethernet/10Base-T, 100Base-TX, IEEE802.11b (wireless LAN)

Transmit function

E-mail

Scan line density

200

100 dpi (Standard character), 200

200 dpi (Detail char-

acter), 200

400 dpi (Fine character)

Original size : Scanning width

, B4 JIS

, A4

Communication Protocols

• Transmission

SMTP, TCP/IP

• Reception

POP3, SMTP, IMAP4, TCP/IP

E-mail format

Single/Multi-part, MIME Conversion

Attached file forms: TIFF-F (MH, MR

, MMR

compression)

Authentication method

SMTP-AUTH, POP before SMTP, A-POP

Internet communication

Send and receive e-mail with a computer that has an e-mail
address

E-mail send functions

Automatic conversion of sent documents to e-mail format and
e-mail transmission. Memory transmission only.

E-mail receive functions

Automatic detection and printing of appended TIFF-F (MH)
files and ASCII text. Memory reception only.

Summary of Contents for Aficio MP 2500













































































































































































































Search results

Summary of Contents for Aficio MP 2500

Reviews:

Related manuals for Aficio MP 2500

Brands by name

Popular brands

Ricoh Aficio MP 2500, Facsimile Reference Manual

Search results

Summary of Contents for Aficio MP 2500

Reviews:

Related manuals for Aficio MP 2500

Brands by name

Popular brands