Ricoh Aficio MP 2500 Facsimile Reference Manual Download

Page: 121 / 204

Setting SEP Codes for Reception

111

Entering a Password

There are times you may want to use a password when receiving faxes by SEP
Code Reception using the SEP Code function.

Note

❒

You can store PWD Codes as well as names and fax numbers in the destina-
tion list.

❒

You can enter numbers,

, and spaces.

❒

The PWD Code is printed on lists and reports.

❒

For the maximum number of digits for the PWD Code, see “Maximum Values”.

Reference

p.186 “Maximum Values”
“Registering Addresses and Users for Facsimile/Scanner Functions”, Gener-
al Settings Guide

SEP Code RX Reserve Report

This report is printed after SEP Code Reception is set up. You can use this report
to check the reservations for SEP Code Reception.

Note

❒

You can turn this function on or off with the User Parameters (switch 03, bit 3)
in the Fax Features menu.

❒

You can have a destination displayed with the User Parameters (switch 04, bit 4)
in the Fax Features menu.

❒

You can display a sender name with the User Parameters (switch 04, bit 5) in
the Fax Features menu.

Reference

“Fax Features”, General Settings Guide

Summary of Contents for Aficio MP 2500













































































































































































































Search results

Summary of Contents for Aficio MP 2500

Reviews:

Related manuals for Aficio MP 2500

Brands by name

Popular brands

Ricoh Aficio MP 2500, Facsimile Reference Manual

Search results

Summary of Contents for Aficio MP 2500

Reviews:

Related manuals for Aficio MP 2500

Brands by name

Popular brands