Ricoh Aficio MP 2500 Facsimile Reference Manual Download | Manualshive

Page: 143 / 204

background image

Printing Options

133

3

Center Mark

When this function is enabled, marks are printed halfway down the left side and
at the top center of each page received.
This makes it easy for you to position a hole puncher correctly when you file re-
ceived documents.

Note

❒

You can enable or disable this function using Center Mark in the Fax Features
menu.

❒

The Center Mark may deviate a little from the exact center of the edge.

Reference

“Fax Features”, General Settings Guide

Reception Time

You can have the date, time, and file number printed at the bottom of the docu-
ment when it is received.

Note

❒

You can turn this function on or off using Print Reception Time in the Fax Fea-
tures menu.

❒

When a received document is split and printed on two or more sheets, the re-
ception time is printed on the last sheet.

❒

The time when the document was printed can also be recorded on the docu-
ment. If you need this function, contact your service representative.

Reference

“Fax Features”, General Settings Guide

«
...
141
142
143
144
145
...
»

Summary of Contents for Aficio MP 2500













































































































































































































Reviews:

No comments

Related manuals for Aficio MP 2500

Brand: Xerox Pages: 168

Brand: Xerox Pages: 36

Brand: Xerox Pages: 64

Brand: Xerox Pages: 54

Brand: Xerox Pages: 2

Brand: Xerox Pages: 115

EasyCoder 501 SA

Brand: UBI Pages: 214

Brand: UBI Pages: 64

Brand: Canon Pages: 4

PIXMA MG3220 series

Brand: Canon Pages: 4

Brand: Canon Pages: 22

Pixma G3020 Series

Brand: Canon Pages: 34

Pixma MG3500 Series

Brand: Canon Pages: 3

Pixma MG7100 Series

Brand: Canon Pages: 4

PIXMA G7000 Series

Brand: Canon Pages: 16

Brand: Canon Pages: 10

Brand: Canon Pages: 4

Brand: Canon Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands