Ricoh Aficio MP 2500 Facsimile Reference Manual Download Page 44

Page: 44 / 204

Transmission

Reference

p.17 “Sending multiple originals using the exposure glass (Memory Trans-
mission)”
p.22 “Sending multiple originals using the exposure glass (Immediate Trans-
mission)”
p.31 “T.37 Full Mode”
p.34 “Acceptable Original Sizes”
p.35 “Paper Size and Scanned Area”
p.37 “If the Machine Cannot Detect the Size of Your Original”
p.38 “Original Sizes Difficult to Detect”
p.39 “Transmission with Image Rotation”
p.41 “Detecting Blank Sheet”
“System Settings”, General Settings Guide
“Placing Originals”, Copy Reference

Acceptable Original Sizes

Where original is set

Acceptable original size

Maximum

number of

sheets

Paper thickness

Exposure glass

Up to A3 (297

420 mm),

11"

17" (279

432 mm)

ARDF,
one-sided document

A5 to A3

(up to 1200 mm long)

" to 11"

17"

50 sheets
(80 g/m

, 20 lb)

40-128 g/m

(10-34 lb)

ARDF,
two-sided document

A5 to A3

(up to 432 mm long)

" to 11"

17"

50 sheets
(80 g/m

, 20 lb)

52-105 g/m

(14-28 lb)

Summary of Contents for Aficio MP 2500













































































































































































































Search results

Summary of Contents for Aficio MP 2500

Reviews:

Related manuals for Aficio MP 2500

Brands by name

Popular brands

Ricoh Aficio MP 2500, Facsimile Reference Manual

Search results

Summary of Contents for Aficio MP 2500

Reviews:

Related manuals for Aficio MP 2500

Brands by name

Popular brands